BACKGROUND: Khat (Catha edulis Forsk) is a stimulant plant grown in East Africa and the Arabian Peninsula. Heavy metal pollution has been a global concern due to its acute and chronic health effects and the major route of exposure is the consumption of contaminated foods. In this study, the determination and health risk assessment of heavy metals (Mn, Cu, Zn, Ni, Cr, Cd, and Pb) in khat and its support soil samples was carried out.
MATERIALS AND METHODS: Khat and its support soil were analyzed for the levels of 7 toxic heavy metals by Atomic Absorption Spectrophotometer. Samples were randomly collected from 3 districts of khat farming kebeles and digested using mixture of strong acids.
RESULTS: The concentrations (mg/kg) of analytes in soil and khat samples were: Cu (6.78-35.80); Zn (24.30-199.02); Mn (7.59-1855.40); Ni (6.37-64.80); Cr (0.82-169.20); Cd (14.2-38.8), and Pb (ND). Among the analyzed heavy metals in soil, Mn was with the highest concentration, followed by Zn, Cr, Cu, Ni, and Cd while that of Zn was the maximum followed by Cu, Mn, and Cr in khat. The levels of Zn, Cr, and Cd in soil samples from all study sites and detected concentrations of Cr in khat samples exceeded the recommended FAO/WHO levels.
CONCLUSION: The hazard index (HI) of metals in khat from study areas was less than 1 indicating a less likelihood of non-carcinogenic toxicological health effects. However, the presence of these toxic chemicals in soil and khat indicates product contamination and needs extensive further investigation involving other heavy metals.
Introduction
Khat (Catha edulis) is a leafy green herbal plant in Celastraceous family. It is commonly grown in East Africa and the Arabian Isthmus, particularly in Yemen.1 An alkaloid named cathinone, accountable for most of the khat’s stimulating effects, is found in its fledgling leaves and stalk tips.2 Its consumption is both a communal and traditional activity and would promote societal interactions. In Ethiopia, it is chewed by teenagers and older people.3,4
Khat is consumed for its stimulating and ecstatic effects, spiritual events and therapeutic purposes. Airway diseases such as cough, asthma and flu are treated by the extracts of khat`s roots and leaves.5 It is also treats ulcers and premature ejaculation in men. Khat`s use is rampant in Middle East, and sub-Saharan African countries including Yemen, Saudi Arabia, Uganda, Eritrea, Ethiopia, Djibouti, Kenya.6
However, regular consumption of khat, particularly in the form of chewing, has been reported to be closely associated with increased susceptibility to hypertension, increased heart rate, and liver problems.7,8 It is also linked to decreased libido, cancer, depression, dental abnormalities, liver damage, and high blood pressure. The psychoactive ingredients cathine and cathinone are believed to be proven precursors of cancer (oral and esophageal) in people who regularly chew khat.9 It is also important to remember that the presence of high levels of toxic metal ions in khat is dangerous and can potentially damage important organs of the body such as the liver and kidneys.8 Since agrochemicals like pesticides are applied to boost productivity, residues on khat leaves may cause cancer and genotoxicity.10
In Ethiopia, khat is consumed daily.11,12 Khat varieties depend on the geographical area of cultivation that includes climate and soil chemistry,1 color and the leaves’ and entire plants size and height.13 Furthermore, it was previously estimated that the high profits of this crop surpasses the earnings from other cereals by almost 2.7-fold.14,15 It is currently one of the top 5 sources of export revenue, and its income for the budgetary year that ended in 2021/22 was $392 million.
Khat is referred to as “green gold” in northern Madagascar as it is a major income source to cover expenditures the expenditure of other items. In most countries like Djibouti, khat consumption is more prevalent in males than females attributing to detrimental effects on the socio-economic circumstances of the general public. A frequent use of khat can cause oral hygiene deterioration necessitating the use of dental plasters. It is worth noting that about 90% of the country’s population regularly consumes khat.16 The prevalence of khat consumption in Ethiopia is 23.22%, especially among which could be endorsed by family chewing behaviors, alcohol intake, and peer pressure. Furthermore, a lifetime incidence of khat munching of 33.2% was reported in the Jazan region of Saudi Arabia.16
Heavy metals are inorganic minerals which are not decomposed by bacteria or other living organisms. Their persistence in the environment can cause acute and chronic poisonousness particularly in animals and humans. The sources of these toxicants in khat could be consistent use of agrochemicals like pesticides and fertilizers and combustion of untreated metal wastes. Heavy metals can also be transferred from polluted soil by geogenic and anthropogenic activities to khat plants. Eventually, lasting risks of health from exposure to heavy metals, both at workplace and environmental, include multiorgan toxicity, including disorders of the interactions between brain, spinal cord and nerves, mental and body energy state processes, body`s ability to fight diseases, ontogenesis, and possibly lasting disability.17 It is reported that Ethiopian khat is polluted by toxic heavy metals including iron, chromium, copper, cobalt, and zinc.18 A study in Yemen has also indicated the presence of zinc, copper, lead, and cadmium. Use of cadmium polluted khat may lead to elevated blood pressure, though its mode of action is not yet clear19 while lead causes nervous breakdown, high blood pressure, cardiovascular disease and cancer. For example, blood with Pb levels between 40 and 60 µg/dL leads to serious health problems if urgent therapeutic measures are not considered.6
A detailed review on prevalence of khat use in different countries, its heavy metal content and associated adverse health effects are available in literature.6 Oyugi et al20 determined the levels of heavy metals in khat using inductively coupled plasma atomic emission spectroscopy (ICP-AES). The mean levels of Pb, Cd, and Cr topped WHO allowable limits. In a study conducted in Ethiopia, the highest level of iron, Fe (37.2-90.3 mg/kg) in khat samples followed by Zn (5.1-10.6 mg/kg), Mn, Ni, Cu and Co while Pb and Cd were undetected.21 Soil samples from the same study sites contained metals in the order of Fe > Mg > Ca > Mn > Zn > Co > Ni > Cu. Cd was detected at levels of 0.73 to 1.23 mg/kg. The Cd, Pb, Cu, and Zn contents of Yemeni Khat were determined by Matloob22 and the levels were in the decreasing order of Zn > Cu > Pb > Cd. The results from a study by State et al23 discovered that the levels of potentially toxic metals are in the order of Mn > Pb > Zn > Ni > Cd > Cu in and soil samples.
Khat cultivation is legal and popular in the Sembeto, Nado, and Chekorsa Doyu kebeles. It is used as a recreational drug on holidays, weekends, cultural ceremonies and other social events. The prevalence of khat consumption by Ethiopian University students was reported to be 23.22%.24 It is also an important source of income. The employment created by khat cultivation is significant, as it involves a large number of people in cultivation, collecting, storage, transport, and sales. Many literatures are existing about the history, taxonomy, pharmacology, chemistry, and socio-economical aspects of Khat,25 but the researches related to the quantification of heavy metals in Khat are limited. However, the concentration of toxic heavy metals and their associated health risks in the prevalently used khat product in the study area is not addressed. Therefore, the objective of the current study was to quantify selected heavy metals in khat and its support soil and assess the risk of khat consumption on human health.
Materials and Methods
Description of study area
Alge sachi district is located in the Ilu Aba Bora zone in Southwestern Ethiopia, located 675 km from Addis Ababa. It is a geographically bordered on the north by the Nole Kabba district (West Wollaga), in the South by the Bilo Nopa district, in the Western by the Darimu district, and Eastern by Mako district (Buno Bedelle). The total area coverage of Alge Sachi district is 84 013 hectares and the total population is around 102 679. The district consists of twenty-eight (28) rural and four (4) towns. Khat leaf and soil samples were randomly collected from 3 khat producing kebeles in the district, namely, Sambo, Chekorsa, Doyu, and Nado.
Reagents chemicals, and materials
Nitric acid (HNO3, 68% (w/w)), sulfuric acid (H2SO4, 98% (w/w)), perchloric acid (HClO4 70% (w/w)), and hydrogen peroxide (H2O2, 30% (w/w)) were chemicals used for sample digestion. Nitrate salts of Manganese (Mn), Nickel (Ni), Lead (Pb), Zinc (Zn), Copper (Cu), Chromium (Cr), and Cadmium (Cd), were used to prepare standards and were analytical grade supplied from Merck, USA, through Addis Ababa, Ethiopia representative. Distilled water was used throughout the analysis.
Apparatuses and instruments
Sterile plastic bags, stainless steel knife, digital analytical balance, ceramic mortar, and pestle, microwave (Model: STRAT D 134348, EVISA), flame atomic absorption spectrophotometer (FAAS) (Buck Scientific, Model 210 VGP, East Norwalk, USA) and drying oven (Model: DHG-9123A) were used in this study. Volumetric flasks, graduated cylinders, and digestion flasks of various volumes were cleaned with cleansing agent, rinsed with distilled water, sodden in 8% HNO3 for 24 hours, rinsed 5 times with double distilled water and dried in an oven.
Sample collection
Composite samples (1 kg) from each sampling site containing 7 subsamples were randomly collected from the 3 kebeles. The khat samples were rinsed a number of times with distilled water after being transported to the laboratory and dried in sunlight for 48 hours to decrease the moisture. Furthermore, they were dried in an oven at 60ºC following peeling and chopping with a Teflon knife followed by grinding to a fine powder using a pestle and mortar. The homogenized samples were kept in air-tight plastic containers and stored until analysis.
Collection of soil samples was carried out beneath the khat at 10 to 30 cm using an auger. A composite sample weighing approximately 2 kg was made by mixing 7 subsamples collected from each farms. After drying for 5 days at room temperature, the grinded and homogenized samples were sieved to pass through a 500 µm mesh. A further oven drying at 60°C occurred for 24 hours and then kept in a clean polyethylene bag till needed for analysis.
Preparations of working standard solutions
Nitrate salts of each metal was used to prepare a 1000 mg/L stock solution. Then 10 mg/L standard solution was prepared, from which 5 different concentrations were made for calibration of FAAS. Dilution was used for the preparation of other working solutions.
Sample digestion
Digestion of khat samples
A 0.5 g of crushed khat powder samples were weighed and transferred to a clean crucible with the sample number. The wet aching was done in a muffle furnace by gradually increasing the temperature to 500°C at which ashing took 5 hours. Then the samples were removed and cooled carefully under a fume hood. The ash was moistened with a little distilled water, then 7 mL of conc. HNO3, 1 mL HClO4, and 2 mL H2O2 in ratio (7:1:2) for each khat sample were added into 100 mL round-bottomed ground-bottom flasks with reflux condenser to digest the samples on the hot plate block digester. After cooling, the digestion, product was filtered into 100 mL reagent bottles using Whatman filter paper #42. The flask was rinsed with filtered distilled water and the samples were then diluted to 100 mL and stored in reagent bottles and stored at 4°C to prevent degradation prior to determination by FAAS.
Digestion of soil samples
Two grams of soil (dry weight) was weighed using a digital weighing scale and the homogenized samples were poured into a 250 mL refluxing block digester. A mixture of HNO3 (70%), H2SO4 (98%), and H2O2 (30%) was added in a volume ratio of 6:2:2 followed by mild heating for 2:45 hours at 100°C. Then the temperature was set to 150°C and heating continued for 2 hours until a clear solution observed. Then, the samples were cooled, filtered with Whatman No.42 filter paper and diluted to 100 mL by distilled water.
Evaluation of the Analytical Methods
Linearity
The method`s linearity was validated by measuring the absorbance of standard solutions of the analytes. It was considered linear when a signal versus concentration gave an R2 > .99 (see Table 1).
Table 1.
Instrument working conditions and correlation coefficients for the determination of metals in soil and khat samples by FAAS.
Recovery test
For the recovery tests, 2 mg/L of Mn, Pb, and Cu, 4 mg/L of Cr and Ni, 3 mg/L of Zn, and 2.5 mg/L of Cd were spiked with a 0.5 g khat in 7 round bottom flasks. Then, digestion was carried out with similar experimental conditions and reagents used for unspiked samples. Spiking experiments were carried out in triplicate for all analytes. The same approach was followed for soil samples.
Human exposure assessment
The human exposure assessment was based on the levels of the metals in khat samples. Khat comes in packs comprising of leaves and stems, and the user consumes an average of 1 pack per day.
Estimated daily intake (EDI)
The amount of khat consumed in 1 day was determined using equation (1)26 with slight modification.
where Ef is frequency of consumption (365 day/year); ED is the duration of chewing (65 years), FIR is the estimated amount of khat used per day (200 g/person/day), CM is the level of the metal (mg/kg dry weight); Cf is concentration conversion factor (0.085).27
Target hazard quotient (THQ)
The health adverse effects of consuming khat polluted with heavy metals was calculated using equations (1) and (2).28
0.014, 0.001, 0.3, 0.04, 0.02, 0.001, and 0.003 were taken as the oral reference doses, RfD for Mn, Cd, Zn, Cu,Ni, Cd, and Pb (mg/kg of body weight per day), respectively. BW (70 kg) was taken as the average body weight of an adult and TA is the total khat chewing duration in life time (65 year × 365 day/year).
Results and Discussion
Method validation
Linearity
The correlation coefficients (R2) of the calibration curve for the analysis of Cd, Cr, Mn, Cu, Zn, Pb, and Ni in soil and khat leaves by FAAS were in the range of .995 to .998, indicating a significant positive correlation between metal levels and absorbance. The FAAS was calibrated with 5 standards. The concentrations used for the calibration, instrument working parameters and the correlation coefficients of the calibration curve for each of the metals are shown in Table 1.
Recovery test
The concentrations of the 7 metals (Zn, Cu, Pb, Cd, Ni, Mn, and Cr) in khat and its support soil samples collected from farms in the 3 main khat growing areas in the Alge-Sachi woredas were determined in triplicate using FAAS. The validity of the method was evaluated by spiking the samples with standards of known levels and calculating the percent recovery expressed as mean ± standard deviation (SD) (n = 3). Percent recoveries for soil and khat leaves were (90.00%-95.00%) and (90.29%-101.59%), respectively, as shown in Tables 2 and 3. The percentage accuracies of the method were also determined by dividing the practically obtained metal concentrations by their respective spiked concentrations.
Table 2.
Recovery and precision results for the determination of metals in soil samples from Sambato kebele.
Table 3.
Recovery and precision test results for the determination of the metal in khat samples (mean ± SD) from Sambato Kebele.
Precision test
The reproducibility of the results was assessed using the relative standard deviation of 3 samples (n = 3) with triplicate readings for each sample. The relative standard deviation (% RSD) for the soil and khat leaves were (0.00722-1.786)% and (0.17-5.114)%, respectively. An analytical method with relative standard deviation (% RSD) <15% and percent recovery (%R) of 70% to 120% is considered valid. Tables 2 and 3 show the % RSD of each metal in each sample.
LoD and LoQ
For the determinations of LoD and LoQ, duplicate analyses were performed for 3 blank samples for all analytes and the pooled standard deviation was calculated. As indicated in Table 4, the LoD for each element is higher than the FAAS detection limit (IDL) but lower than the levels of metals detected signifying the method’s appropriateness for quantification of the analytes at trace levels. The differences in the LoD and LoQ’s of the khat and soil was due to the differences in the standard deviations of the blank signals measured at different times.
Table 4.
IDL, LoD, and LoQ of the analytes.
Determinations of heavy metals in khat and its support soil
The concentration of selected heavy metals (Mn, Zn, Ni, Cd, Pb, Cu, and Cr) in khat and soil of the 3 khat growing areas of Sembeto, Chokorsa Doyu, and Nado kebeles were determined with FAAS. The mean levels of the studied metals are depicted in Table 5.
Table 5.
Levels (mg/kg) of heavy metals in soil and khat in the 3 kebeles.
Levels of heavy metals in khat samples
As it can be seen in Table 5, Mn, Cu, and Zn were present in all khat samples from the 3 kebeles with level ranges (mg/kg) of 7.59 ± 0.95 to 10.48 ± 0.84, 6.78 ± 0.71 to 25.68 ± 0.49, and 24.30 ± 0.65 to 29.89 ± 1.02, respectively. The levels of metals in khat leaves from Sambato kebele follows the order Zn > Cu > Mn > Cr while Pb and Cd couldn’t be detected by the employed method. The low copper level in samples from Nado kebele compared to samples from Chokorsa Doyo and Sambato kebeles could be due to the form of copper in the soil, pH, organic matter content and clay composition. Nevertheless, there is a research indicating the presence of Pb and Cd in Yemeni khat leaves with concentration of 0.066 to 0.7 mg/kg and 0.007 to 0.018 mg/kg, respectively.29 The samples from Chokorsa Doyu kebele follow the same trend except the presence of Ni and absence of Cr. Khat leaves from Nado sampling sites detected positive for Zn, Mn, Cu, and Cr with concentrations of 24.30 ± 0.65, 8.42 ± 0.59, 6.78 ± 0.71, and 3.49 ± 0.15 mg/kg, respectively. The highest levels of Mn (10.48 ± 0.84 mg/kg), Cu (25.68 ± 0.49 mg/kg), Zn (29.89 ± 1.02 mg/kg), and Ni (6.37 ± 0.24 mg/kg) were recorded in samples from Chokorsa Doyu and that of Cu (35.80 ± 0.88 mg/kg) and Cr (3.49 ± 0.15 mg/kg) were from Nado kebele. From the studied analytes, only the concentrations of Cr in khat samples from Sambato and Nado sites exceeded the recommended level (0.25 mg/kg) by FAO/WHO.
A study in Saudi Arabia determined the highest concentrations of Cu (215.4 ± 12.3-3054 ± 45.2 mg/kg), Mn (108 ± 5.8-1541 ± 24.7 mg/kg), Zn (23.17 ± 0.4-1490 ± 32.6 mg/kg), Pb (0.18 ± 0.87 mg/kg), and Cd (0.00 ± 0.08 mg/kg) in khat leaves.30 The level of chromium in the soil and its likely human health risk on the chewers was also evaluated.31 A 71.01 ± 12.05 to 317.55 ± 23.14 mg/kg was obtained for soil while khat leaves contained 6.5 ± 1.76 to 30.01 ± 2.91 mg/kg total chromium, a value that comprises the present study.31 The levels of Pb, Cd, Zn, and Cu in Ethiopian khat were 0.18 to 0.87 mg/kg, 0.15 ± 0.90, 0.10 to 41.80, and 25.15 to 73.95 µg/g, respectively.11 FAAS/OES GFAAS using an external calibration curve was used in analysis of 13 metals and the levels (mg/kg) were reported as Cu: 5.11 to 9.55, Cd: 0.03 to 6.54, Pb: non-detectable to 1.57, Zn: 4.15 to 89.3, Mn: 6.45 to 20.32 A study conducted by Fentie Tadesse18 analyzed khat cultivated Gidolle, Konso and Koyira and reported the results (µg/g) as: Fe (180-222), Zn (25.23-33.69), Cu (12.64-15.74), Cr (4.01-4.53), while Pb and Cd were not detected.
In a study conducted by Oyugi et al20 in Kenya, the mean heavy metal concentrations (mg/kg) in dry khat samples of 6 toxic heavy metals were Cd (7.81 ± 1.56), Cr (15.98 ± 2.22), Cu (15.81 ± 2.84), Fe (97.35 ± 32.67), Ni (0.37 ± 0.02), and Pb (32.36 ± 9.95) in which the levels of Pb, Cd, and Cr surpassed WHO acceptable bounds. In a study done by Matloob22 on khat samples, 20.3 ± 10.3, 233.6 ± 141.5, 5308 ± 1888, 6622 ± 1822 µg/kg were obtained for Cd, Pb, Cu, and Zn, respectively. The levels of essential and non-essential metals in Ethiopian khat samples in fresh-weight basis were reported in the order: Ca (1038-2173 µg/g) > Mg (478.2-812.3 µg/g) > Fe (53.95-82.83 µg/g) > Zn (5.18-9.40 µg/g) > Mn (6.98-8.66 µg/g) > Cu (1.85-5.53 µg/g) > Cr (0.66-3.47 µg/g) > Co (0.41-0.80 µg/g).33 The variation between the current studies from results in the literature could be differences in the nature and type of soil as these are considered the most key feature that governs the incidence of heavy metals as it serves as the retention and binding site for several toxic materials. Moreover, the type and dose of fertilizer and pesticide usage affect the levels of these metals in khat samples.
Levels of heavy metals in soil
The contents of plant elements are conditional, and they depend on soil properties and plant capacity to selectively accumulate certain metals. It is also known that these elements can have a detrimental effects on plant growth, soil cover and, fertility.34 From the studied 7 heavy metals, all of them were detected in soil samples except Pb. The levels follow different order in the samples from 3 kebeles. However, Mn was found with the highest concentration in all samples from the study sites. The reported levels (mg/kg) of the metals from Sambato kebele follow the order: Mn (1724.60 ± 0.52) > Zn (199.02 ± 0.73) > Cr (66.60 ± 0.64) > Ni (40.2 ± 0.42) > Cu (29.00 ± 0.94) > Cd (14.2 ± 0.24). For the soil samples analyzed from Chokorsa Dayu, the results (mg/kg) were: Mn (1855.40 ± 0.72) > Cr (92.20 ± 0.82) > Zn (87.90 ± 0.19) > Ni (52.6 ± 0.61) > Cu (31.40 ± 0.35) > Cd (26.6 ± 1.10). As can also be seen from Table 5, the concentrations (mg/kg) of the 6 metals in soil from Nado kebele were, in decreasing order 1197.60 ± 0.48, 169.20 ± 2.17, 87.66 ± 1.42, 64.8, 38.8, and 35.80 ± 0.88 for Mn, Cr, Zn, Ni, Cd, and Cu, respectively. Similarly, the highest levels of 4 of the 6 metals were determined in soil from Nado kebele as follows: Cu (35.80 ± 0.88), Cr (169.20 ± 2.17), Ni (64.8 ± 0.86), and Cd (38.8 ± 0.95). A 1855.40 ± 0.72 and 199.02 ± 0.73 mg/kg were recorded as the maximum concentrations of Mn and Zn from Chokorsa Dayo and Sambato kebeles, respectively. The levels of Zn, Cr, and Cd in soil samples from all study sites are above the recommended FAO/WHO levels set at 50, 50, and 1 mg/kg, respectively.
In a study done in Tanzania on soil, Fe was found with the highest concentration followed by Zn, Pb, and Cu. The concentrations (mg/100 g dry soil) of the metals were 2760.1 to 2833.07, 15.5 to 20.13, 305.95 to 308.25, 224.48 to 230.39 for Fe, Cu, Zn, and Pb, respectively.35 Similarly, in the soil samples irrigated with wastewater in and around Asmara, Eritrea, heavy metals were detected in the concentration order of Mo < Cd < Co < Cu < Pb < V < Cr ≈ Zn < Mn < Fe < Al indicating that Fe, Mn, and Pb has exceeded FAO/WHO limits.36
In the present study, the mean concentrations of the 6 metals were compared using ANOVA. There were no significant differences (P = .54, α = .05) among the mean levels of each metals in soil between the 3 kebeles. However, the levels of the different metals (within each 3 kebeles differ significantly (P = 8.3 × 10−7, α = .05). The same trend was also revealed by for metal concentrations of khat samples within and between the kebeles. The calculated P-values of metals concentration variations for the within and between kebeles were .000108 and .206585, respectively. The variation of the metal contents from different sampling sites might be attributed to regular use of fertilizers, incineration of scrap of metals and application of pesticides.32,37 Heavy metals can also be absorbed from contaminated soils.
Determination of transfer quotients
Transfer quotient is the ratio of metal’s concentration in khat to soil with the assumption that metals in khat come from soil. The transfer coefficient exhibited reduced concentration with values of 0.004 to 0.818, as shown in Table 6. The finding indicates that Cu has the highest transfer coefficient followed by Zn, Ni, Cr, and Mn. The uptake and bioaccumulation of heavy metals depend on the bioavailability, levels in soil, the chemical form, plant uptake capabilities, and plant species growth rate.38 The higher transfer coefficients of Cu and Zn might be attributed to their higher mobility but lower retention with in soil than other metals. It is also reported that high value transfer factor indicates low retention capacity.39 Similarly, TF exceeding 1 shows hyperaccumulation, particularly in soils17 but TF of 0.1 showed that the plant was excluding metals from its tissues, while the TF values of 0.2 indicated the likelihood of metal pollution by anthropogenic undertakings.39
Table 6.
Soil-Khat transfer coefficient (%) of heavy metals.
Human health risk assessment
The human health risk associated with consumption of meat contaminated khat were assessed using estimated daily intake, hazard quotient and hazard indexes. The results are shown in Table 7.
Table 7.
Estimated daily intake (mg/kg bw) and hazard quotient of various elements for different Khat varieties.
As shown in Table 7, for the 7 heavy metals studied, all their corresponding EDIs were less than the corresponding provisional tolerable daily intakes, and did not approach the doses. The finding showed the highest estimated daily intake values of zinc in all samples fooled by Cu and Mn. The EDI value of Cr is higher in samples from Sambato than in Nado and Ni had the lowest EDI than other metals for samples from Chokorsa Doyu. For samples from Sambato kebele, the THQ follows the order: Zn > Cu > Mn > Cr while it is Mn > Cu > Ni > Zn for Chokorsa Doyu khat samples. Nado samples had THQ of 0.144, 0.041, 0.02, and 0.0006 for Mn, Cu, Zn, and Cr, respectively. According to Vinet and Zhedanov,40 THQ > 1 indicates a higher possibility of occurring for non-cancer health disorders. Since the THQ of the metals for all samples is less than 1, chewing of khat has less likelihood to cause non-cancerous adverse health effects with respect to the studied heavy metals. The hazard index (HI) calculated as the sum of the THQs of all metal ions is also less than 1 indicating less likelihood of non-carcinogenic toxicological health effects. However, the results of EDI, THQ and HI were calculated considering amount of khat used per day to be 200g, and the average body weight of an adult as 70 kg. These values are estimations and the mass of khat consumed per day could be higher and the considered weight could also be lower as this plant is even commonly used by young generations. But it’s possible for chronic and synergistic effects to occur even when the estimated daily intake (EDI) of heavy metals is less than 1. The concept of EDI primarily considers the average daily intake of a substance over a given period. However, chronic and synergistic effects can result from long-term exposure to low levels of multiple heavy metals, even if the intake of each metal individually remains below a certain threshold. Furthermore, the toxicity of heavy metals can be influenced by various factors such as the route of exposure, duration of exposure, individual susceptibility, and interactions with other chemicals or pollutants present in the environment.
Conclusion and Recommendation
The content of some selected heavy metals Mn, Ni, Cu, Zn, Pb, Cd, and Cr in khat and soil samples from the 3 kebeles of Alge Sachi Woredas was determined using FAAS. The developed analytical method was validated and acceptable values of parameters were obtained. The levels of Zn, Cr, and Cd in soil samples from all the study sites and detected concentrations of Cr in khat samples exceeded the recommended FAO/WHO levels. However, the health risk assessments indicated that the hazard index (HI) of metals in khat from study areas was less than 1 indicating a less likelihood of non-carcinogenic toxicological health effects. The high TF values (>20%) of Cu and Zn show the likelihood of metal contamination by anthropogenic activities. It is recommended that a better understanding of the health effects and chemical composition of khat should be established through a multidisciplinary approach involving khat producers as most of them use fertilizers and pesticides to increase product yield without considering their detrimental health effect on consumers. Moreover, a study encompassing large number of samples from all districts in the Ilu Ababor Zone and ICP-MS as a detection technique considering other toxic heavy metals may lead to a more comprehensive and representative report.
© The Author(s) 2024
This article is distributed under the terms of the Creative Commons Attribution-NonCommercial 4.0 License ( https://creativecommons.org/licenses/by-nc/4.0/) which permits non-commercial use, reproduction and distribution of the work without further permission provided the original work is attributed as specified on the SAGE and Open Access pages ( https://us.sagepub.com/en-us/nam/open-access-at-sage).
Author Contributions
All authors contributed to the study conception and design. Material preparation, data collection and analysis were performed by Shibiru Damana, Ibrahim Umer, and Abiyot Kelecha. The first and final draft of the manuscript was written by Abiyot Kelecha and all authors commented on both versions of the manuscript. All authors read and approved the final manuscript.
Ethical Approval
Not applicable.
Consent to Participate
Not applicable.
Consent for Publication
All the authors give their consent for publication of the manuscript.
